英语词典
roll bending
[机]轧辊挠度；滚筒弯曲加工
相似词语短语bending───n.弯曲，弯曲度；v.弯曲（bend的现在分词）
flatwise bending───平面弯曲
bending over───俯身；折转
flexural bending───塑性弯曲
anticlastic bending───抗塑性弯曲
bending moment───[力]弯矩；[力]弯曲力矩；[力]挠矩；弯（曲）矩，挠矩
roll───n.(Roll)（美、挪、加）罗尔（人名）；v.滚动；翻身；（眼睛）转动；在原地打滚；（马）仰卧蹬脚；左右摇晃；蹒跚；使翻车；掷（骰子）；掷出（骰子数）；（转动）肩膀；行驶；推；摇车窗；（液体）滚落；（时间）流逝；稳定持续的；（产品）从（机器）产出；涌流；延绵起伏；运转；卷，卷起；展开；搓成；辗；发出隆隆声；把（衣服的边）卷起来；压平；覆盖；启动；用颤音发出（辅音，尤其是r）；n.卷；柱形物；卷状食品；滚动；翻筋斗；左右摇晃；隆隆声；小面包；总人数；名单；公文；延绵起伏；辊轧机；一管；掷骰子
mutton roll───羊肉卷
french roll───法国式小面包；法式小面包；单面印刷卷筒纸
双语使用场景Avoid high stress concentrations at the ends of the work roll barrel. Ensure good control of roll bending.───避免在工作辊辊端部位应力过于集中。确保弯辊得到很好的控制。
work principle and technical advantages of two-axle roll bending with elastic medium(RSEM) are described.───介绍了两轴柔性滚弯的工作原理和技术优势。
Nearly all rolling mills are fitted with work roll bending equipment.───几乎所有的轧机均安装了工作辊弯曲装置。
Realization of three models, including roll-bending feedforward, crown feedback and flatness feedback, on field was described in detail.───本文详细阐述了弯辊力前馈、凸度反馈和平坦度反馈三个模型在现场的具体实现。
The work principle and technical advantages of two-axle roll bending with elastic medium(RSEM) are described.───介绍了两轴柔性滚弯的工作原理和技术优势。
roller excircle rugged roll bending straight, " " marks caused by the location of the usual bite.───不朱辊外圆高低不服辊芯笔屈不屈，引起“条痕”的场所凡是在咬口处。
Improvement of the Roll Shape and Reduction of the Roll Bending Force for Increment of Life of the Work Roll Bearing and Roller───改善辊型降低弯辊力提高工作辊轴承及轧辊使用寿命
Calculation and Determination Method for Empirical Setting Parameters of Three- roll Bending- plate Internally- supporting Welded Pipe Mill───三辊弯板内承式机组经验调型参数计算及确定方法
Calculating of the Cold-rolled Forming Section Trough Steel during Roll Bending Formation Course───冷弯型钢槽型钢辊弯成型过程计算
英语使用场景The change of strip crown is in direct proportion with work roll shifting distances and roll bending force and the square of strip width.
Special Mill Features : Hydraulic Automatic Gauge Control. Positie and Negatie Work Roll Bending. Intermediate Roll Shifting.
An independent module of work roll bending compensation is set in the feedback control system.
roll bending
